For a better experience, please enable JavaScript in your browser before proceeding. When it comes to things like filter installations, they are quite handy. There is no warrenty info on the package. They can even be used outside because they are UV resistant and wont damage like the O-rings on a SharkBite fitting. If you plan on working with copper pipes, you cant go wrong with SharkBite fittings, either. Another major difference between the two is how they connect. If you have never made a mistake, you haven't done much. The body is designed to hold up to greater pressure and temperature requirements, ensuring that it wont degrade or melt in applications like hot water heaters. SharkBite has a push-to-connect design in that, when you push it onto a piece of tubing or a pipe, the teeth will clench down with a push. There is a removable insert in the SharkBite fitting that moves the collect. The teeth are of a durable construct, ensuring that they grip onto the piping or tubing securely and wont bend or break. You can bet that you are getting durability and structural stability with the brass body design. This is why I always tell people to check with their local Code office. So, while you can use them for a variety of fixes or installations, they really are better for predesigned applications. Your beef should be with Menards, not Watt's. That said, both Watts and SharkBite have their ideal applications. Thats not to say they cant be used for PVC, but they have a better natural fit with copper for the reasons mentioned. link to How To Keep Centipedes Out Of Your Bed. That may give them different applications than the Watts fitting though the differences end up being minor in nature. When spaces are tight, slapping on a quick-connect fitting to PVC or PEX tubing, or even copper piping, can make things all the easier. -Redgreen. That is why quick-connect fittings have become so prominent. Being made of a sturdier material, SharkBite fittings are less prone to cracking due to freezing temperatures. Really, you cant go wrong with either. The teeth on the collet grip onto tubing or piping to form a secure hold. You must log in or register to reply here. The simple fact of the matter is that both have their own designated purposes and uses. I've had my doubts about those too for DHW lines. Stupid me did not check to see if there was a warrenty on their material. thats great. My bro-inlaw used it no probs and loves it. The spec sheet says it, the warranty says it, the ratings show it (max temp listed is 140 degrees for a pressure rating). A forum community dedicated to Do it yourself-ers and home improvement enthusiasts. But you are quite right, the series 35 has a higher temp rating even though it's still not intended for boilers. You can bet that you are getting durability and structural stability with the brass body design. Has anyone used the Watts Quick Connect Fittings? They can be used in tandem or on projects that may not be in their wheelhouse, though that typically is not advisable. I stopped at Menards tonight. But that is not even the biggest difference when it comes to the collet. , Fiskars 8lb Isocore maul, Fiskars XA22 hookaroons, Dirty Hands Tools 22 ton half beam splitter. Ryan also loves hockey and a lifelong Buffalo sports fan. JavaScript is disabled. The SharkBite fitting cannot be disassembled. It does so in order to lock the tubing down and keeps the tubing from being able to back out. I think these are approved for DHW lines and plan to use pex with these in my basement finishing if that is the case. I would check with the local Code office before using them. For a better experience, please enable JavaScript in your browser before proceeding. Find out the difference between SharkBite and compression fittings. 
Though they serve the same purpose and function, there are important design differences between the two fittings. Helping You to Do It Yourself! How did you like it? We will get into each one but both are quite reliable and sturdy. In my opinion, they are "still" a compression fitting and most codes do not allow them in areas that are not readily visable. So ensuring it is free of any Get free, zero-commitment quotes from pro contractors near you. When you are installing hot water heaters, SharkBite fittings are probably the best option. Enter Our Dog Days of Summer BBQ Giveaway Now! No leaks in 7 years. Additionally, these brass fittings are a better match for copper piping. Nicely done. It is important that the teeth be pushed out of the way if you are using a disconnect tool to eventually release them.
Great for implementing repairs without having to replace the entire quick-connect fitting. I used the brass barbed fittings to sweat to copper or thread into pumps, etc. I probably have at least 35 of these fittings in 1/2, 3/4 and one 1 inch. They are both versatile, durable and make piping/tubing repairs and installation far quicker and easier. The downside is that they dont work all that well on copper piping. The rubber is both flexible and durable, and it is also easy to replace in the event of wear and tear or damage. But since this is the internet Anyways Watts makes different series connectors with different max temperature's. The collect can be removed whenever necessary to implement a repair, so you dont have to spend the money on a new fitting nor the time to re-install it again. watts connect quick cts coupling aqualock That said, they can be quite a bit costlier than their counterpart. pex cpvc aqualock watts If you want something graded for outdoor use or that has more flex to it, Watts is a great choice. Before we get into the comparison of the two, it helps to know what a quick-connect fitting is in the first place. So, while you can use them for a variety of fixes or installations, they really are better for predesigned applications. I here they can be used with PEX Copper and Cpvc. The teeth from the twist-lock will tighten when you try to pull the fitting off, ensuring that it is not going anywhere. They are also really cost-effective so it is not unreasonable to buy some extras to keep in case of an emergency. SharkBite, for example, is a type of quick-connect fitting. It's the "wording" that is important. But what is the difference between the two? Your bed is the place in your home that should bring you the most peace, tranquility, and comfort. The SharkBite connect makes the connection secure and prevents movement. Even better, those smaller fittings tend to be interchangeable with compression fittings. . Even better, those smaller fittings tend to be interchangeable with compression fittings. When it comes to plumbing repairs and installations, being simple and efficient is key. I had an inspector tell me that "code compliant" was not "code accepted". It was extremely easy and no leaks yet. 6 months with my Sharks from HomeDepot and no problems. I think I installed them 2012.
Most importantly, Watts fittings can be repaired. Those Watt's quick connect fittings are clearly intended for potable water systems only. For one, SharkBite has a brass body design. Having either at your disposal would make the job a lot easier. Did you ever have any luck with this? The brass body construction is part of what makes SharkBite such a reliable option. I am in the process of changing out all of them because 5 of them have started to leak. 
Those rubber O-rings are meant to seal off leaks but can wear and deteriorate over time. Blue Hawk vs. Sharkbite Push-Fit Fittings: Which One is Better? About 5 yrs. Watts quick connects are rated for a maximum of 180 degree water at 100psi. , for example, is a type of quick-connect fitting.
The collect can be removed whenever necessary to implement a repair, so you dont have to spend the money on a new fitting nor the time to re-install it again.
I was visiting the site to find out if anyone had any reliability information on them. After all, what good would a fitting be if water managed to find its way through? Watts has a fitting that you can disassemble. Is one better than the other? I merely quoted manufactured published data. This is another major difference between Watts and SharkBite. He loves to blog about construction, plumbing, and other home topics. Why is this big? First and foremost, it bears stating that they can be used in various applications. Compression Fittings (Here Are The Differences). Those little teeth one would say like a shark that wrap around the collect is what grips the tubing or piping. Not only that, but the collect cant be removed. In my honest opinion these fittings are crap.
I just bought the $30-40 crimper and used the Watts stainless steel crimps that come in a bag for my boiler stuff. That is because Watts and its plastic body are much more flexible, working better with the flexibility of the plastic piping. The brass body construction is part of what makes SharkBite such a reliable option. JavaScript is disabled. They can even be used outside because they are UV resistant and wont damage like the O-rings on a SharkBite fitting. The O-ring, meanwhile, provides an airtight seal that ensures there are no leaks. But we were very happy with how easy and fast all his hookups went rather it was from pex to pex, or pex to copper. When spaces are tight, slapping on a quick-connect fitting to PVC or PEX tubing, or even copper piping, can make things all the easier. Plastic may not have the durability that brass does, but it is less prone to cracking because it has the flexibility to expand and contract with temperature changes. I used shark bites with my pellet boiler, no issues with 180+ water, of course my system was unpressurized. The most glaring difference between the Watts fitting and the SharkBite fitting is the material used to construct the body. When it comes to things like filter installations, they are quite handy. Those are series 10 quick connects which i'm not sure Menards even carries those. First and foremost, it bears stating that they can be used in various applications.
That brass is lead-free, which allows them to have a higher pressure can temperature tolerance than similar fittings constructed of plastic. The locking mechanism is meant to prevent the connection from falling apart when the faucet is turned off, causing the flow to suddenly stop. No soldering! As with anything, get the right connector for what you will be using it for. Plastic tends to be more optimal for tubing. I use John Guest, not Watts. The Fora platform includes forum software by XenForo, VerticalScope Inc., 111 Peter Street, Suite 600, Toronto, Ontario, M5V 2H1, Canada. SharkBite is also approved for use behind walls and underground, but that is a risk. The SharkBite makes use of a push-to-connect feature where teeth grab onto the tubing or piping. Both of them have an O-ring and collet within the body. You are using an out of date browser. There may be subtle differences between it and the Watts brand, but the concept is the same. 
I use quick connect fittings (1/4 and 3/8) under the sink for the under the sink filter that feeds into the filtered cold and instant hot water dispenser and the ice maker. Watts brass quick connects are rated for 250 degrees at 80psi. Last year I helped my neighbor install his OWB system, and he chose to use Watts quick connectors, which is what was recommended by Menards for pex fittings. Orlan EKO 40, Forced Air Furnace HX - Sold to a good home. I went back to Menards to find out if there any issues, only to find out there is a 1 yr. warrenty on their products. They make it easier for plumbers to get in, get the job done, and move on to the next task. It may not display this or other websites correctly. The O-ring is there to create the leak-proof seal. Whereas SharkBite uses brass for the body, Watts uses a plastic material for its quick-connect fittings instead. Ryan Womeldorf has more than a decade of experience writing. When it comes to a quick repair or an easier installation, both will come in handy. That means if there is any damage to the SharkBite quick-connect fitting, it has to be replaced entirely. look on the label for ", "If the women don't find you handsome, they should at least find you handy. " Come join the discussion about tools, projects, builds, styles, scales, reviews, accessories, classifieds, and more! Though they both have teeth gripping the collect, Watts has fewer teeth. Quick-connect fittings are named because they are fast and easy to install. SharkBite fittings and their brass construction are meant to hold up to higher temperatures. Isn't it amazing that they can join the dissimilar pipes(pex w copper). Are there any tricks? That is not to say that one is worse than the other, but there are clear differences that may influence your choice when it comes time for the repair or installation. You'll notice the warranty policy is the same for series 35 and 45potable water system use only. Nightstands are valuable pieces of your bedrooms design, adding both form and function to the space. Two of the most common options out there for quick-connect fittings are Watts and SharkBite. SharkBite vs. ago I replumbed my utility room water lines using Watts brass and pvc pex fittings. In that instance, they are out of sight which means you would not know if a leak was present. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
DO NOT BUY WATTS FITTINGS!! When it comes down to it, both the Watts and SharkBite quick-connect fittings have their own unique benefits and uses. Real pain to need to go back and replace when you have other things to do.
If you plan to work with plastic tubing or piping, then the Watts fitting would be better. Not only that, for applications where temperatures are higher, you run the risk of degradation and melting whereas SharkBite would not have that issue. The most glaring difference between the Watts fitting and the SharkBite fitting is the material used to construct the body. After all, what good would a fitting be if water managed to find its way through? The brass ones were the ones setup on their boiler display at the store I was at. Despite their similarities, there are differences between the SharkBite and Watts quick-connect fittings. The worst problem comes when you attempt to sell a home and the buyer hires a Home Inspector who questions these fittings. I am replacing all of the brass ones with the pvc ones for now as they are the ones leaking. I have used many Watts products and they make quality stuff, but that doesn't make them legal. It has been 4 weeks and no leaks. If you have ever worked with a Code inspector, you know that they can have attitudes if you try show or tell them that something is Code Approved. There are specific situations where you would want to use your SharkBite fittings versus when you would want to use Watts fittings. The teeth from the twist-lock will tighten when you try to pull the fitting off, ensuring that it is not going anywhere. Before we get into the comparison of the two, it helps to know what a quick-connect fitting is in the first place. Here are the ones Menards carries since this is the internet. They are both flexible and they both work with each other in a give-take relationship. Indeed. The selling point is in the quick-connect ability. Those rubber O-rings are meant to seal off leaks but can wear and deteriorate over time. . i don't know about watts in particular, but i have used other compression fit. On the other hand, Watts fittings are much better wherever PVC or plastic tubing is involved. At some point in the future I will again have to replumb my utility room with a more permanent product. There may be subtle differences between it and the Watts brand, but the concept is the same. http://media.wattswater.com/ES-QC-10Tees.pdf, http://www.watts.com/pages/_products_details.asp?pid=6632, Ducted heatpump sharing ducts with Wood/oil combo.
Is it possible to disconnect Central Boiler & install an electric boiler connected to the heat exchanger instead. If you plan on working with copper pipes, you cant go wrong with SharkBite fittings, either. Watts fittings are better for small diameter tubing, too. I want to rough in the supply lines for my bar bath and Mud sink. Using them outside runs the risk of the rubber O-ring cracking or splitting. My 2nd season in since using the quick connects I'm finding most off them leak after the system cools down. 
It tied the old copper piping to new Pex with no problems yet. He deliberated for a while about it because they are so expensive per fitting. I just replumbed part of the house with the Watts quick connect fittings. Using them outside runs the risk of the rubber O-ring cracking or splitting. The teeth are of a durable construct, ensuring that they grip onto the piping or tubing securely and wont bend or break. That brass is lead-free, which allows them to have a higher pressure can temperature tolerance than similar fittings constructed of plastic. The lead-free brass is quite rigid in the same way that a pipe is and can stand up to higher pressure tolerances as well. The rubber is both flexible and durable, and it is also easy to replace in the event of wear and tear or damage. Well, if the fitting is damaged, you can potentially repair it whereas the SharkBite fitting would simply need to be replaced. The Boiler Room - Wood Boilers and Furnaces. They have their own books and don't care how many website copies from fitting manufacturers you show them. SharkBite tends to go best in applications where a sturdier connection is required. After all, most people spend nearly one-third of every day in bed. In that instance, they are out of sight which means you would not know if a leak was present. Help! Watts quick-connect fittings have a locking mechanism that twists.
Though they serve the same purpose and function, there are important design differences between the two fittings. Helping You to Do It Yourself! How did you like it? We will get into each one but both are quite reliable and sturdy. In my opinion, they are "still" a compression fitting and most codes do not allow them in areas that are not readily visable. So ensuring it is free of any Get free, zero-commitment quotes from pro contractors near you. When you are installing hot water heaters, SharkBite fittings are probably the best option. Enter Our Dog Days of Summer BBQ Giveaway Now! No leaks in 7 years. Additionally, these brass fittings are a better match for copper piping. Nicely done. It is important that the teeth be pushed out of the way if you are using a disconnect tool to eventually release them. Great for implementing repairs without having to replace the entire quick-connect fitting. I used the brass barbed fittings to sweat to copper or thread into pumps, etc. I probably have at least 35 of these fittings in 1/2, 3/4 and one 1 inch. They are both versatile, durable and make piping/tubing repairs and installation far quicker and easier. The downside is that they dont work all that well on copper piping. The rubber is both flexible and durable, and it is also easy to replace in the event of wear and tear or damage. But since this is the internet Anyways Watts makes different series connectors with different max temperature's. The collect can be removed whenever necessary to implement a repair, so you dont have to spend the money on a new fitting nor the time to re-install it again. watts connect quick cts coupling aqualock That said, they can be quite a bit costlier than their counterpart. pex cpvc aqualock watts If you want something graded for outdoor use or that has more flex to it, Watts is a great choice. Before we get into the comparison of the two, it helps to know what a quick-connect fitting is in the first place. So, while you can use them for a variety of fixes or installations, they really are better for predesigned applications. I here they can be used with PEX Copper and Cpvc. The teeth from the twist-lock will tighten when you try to pull the fitting off, ensuring that it is not going anywhere. They are also really cost-effective so it is not unreasonable to buy some extras to keep in case of an emergency. SharkBite, for example, is a type of quick-connect fitting. It's the "wording" that is important. But what is the difference between the two? Your bed is the place in your home that should bring you the most peace, tranquility, and comfort. The SharkBite connect makes the connection secure and prevents movement. Even better, those smaller fittings tend to be interchangeable with compression fittings. . Even better, those smaller fittings tend to be interchangeable with compression fittings. When it comes to plumbing repairs and installations, being simple and efficient is key. I had an inspector tell me that "code compliant" was not "code accepted". It was extremely easy and no leaks yet. 6 months with my Sharks from HomeDepot and no problems. I think I installed them 2012.
Most importantly, Watts fittings can be repaired. Those Watt's quick connect fittings are clearly intended for potable water systems only. For one, SharkBite has a brass body design. Having either at your disposal would make the job a lot easier. Did you ever have any luck with this? The brass body construction is part of what makes SharkBite such a reliable option. I am in the process of changing out all of them because 5 of them have started to leak. The collect can be removed whenever necessary to implement a repair, so you dont have to spend the money on a new fitting nor the time to re-install it again.
I was visiting the site to find out if anyone had any reliability information on them. After all, what good would a fitting be if water managed to find its way through? Watts has a fitting that you can disassemble. Is one better than the other? I merely quoted manufactured published data. This is another major difference between Watts and SharkBite. He loves to blog about construction, plumbing, and other home topics. Why is this big? First and foremost, it bears stating that they can be used in various applications. Compression Fittings (Here Are The Differences). Those little teeth one would say like a shark that wrap around the collect is what grips the tubing or piping. Not only that, but the collect cant be removed. In my honest opinion these fittings are crap.
I just bought the $30-40 crimper and used the Watts stainless steel crimps that come in a bag for my boiler stuff. That is because Watts and its plastic body are much more flexible, working better with the flexibility of the plastic piping. The brass body construction is part of what makes SharkBite such a reliable option. JavaScript is disabled. They can even be used outside because they are UV resistant and wont damage like the O-rings on a SharkBite fitting. The O-ring, meanwhile, provides an airtight seal that ensures there are no leaks. But we were very happy with how easy and fast all his hookups went rather it was from pex to pex, or pex to copper. When spaces are tight, slapping on a quick-connect fitting to PVC or PEX tubing, or even copper piping, can make things all the easier. Plastic may not have the durability that brass does, but it is less prone to cracking because it has the flexibility to expand and contract with temperature changes. I used shark bites with my pellet boiler, no issues with 180+ water, of course my system was unpressurized. The most glaring difference between the Watts fitting and the SharkBite fitting is the material used to construct the body. When it comes to things like filter installations, they are quite handy. Those are series 10 quick connects which i'm not sure Menards even carries those. First and foremost, it bears stating that they can be used in various applications.
That brass is lead-free, which allows them to have a higher pressure can temperature tolerance than similar fittings constructed of plastic. The locking mechanism is meant to prevent the connection from falling apart when the faucet is turned off, causing the flow to suddenly stop. No soldering! As with anything, get the right connector for what you will be using it for. Plastic tends to be more optimal for tubing. I use John Guest, not Watts. The Fora platform includes forum software by XenForo, VerticalScope Inc., 111 Peter Street, Suite 600, Toronto, Ontario, M5V 2H1, Canada. SharkBite is also approved for use behind walls and underground, but that is a risk. The SharkBite makes use of a push-to-connect feature where teeth grab onto the tubing or piping. Both of them have an O-ring and collet within the body. You are using an out of date browser. There may be subtle differences between it and the Watts brand, but the concept is the same. I use quick connect fittings (1/4 and 3/8) under the sink for the under the sink filter that feeds into the filtered cold and instant hot water dispenser and the ice maker. Watts brass quick connects are rated for 250 degrees at 80psi. Last year I helped my neighbor install his OWB system, and he chose to use Watts quick connectors, which is what was recommended by Menards for pex fittings. Orlan EKO 40, Forced Air Furnace HX - Sold to a good home. I went back to Menards to find out if there any issues, only to find out there is a 1 yr. warrenty on their products. They make it easier for plumbers to get in, get the job done, and move on to the next task. It may not display this or other websites correctly. The O-ring is there to create the leak-proof seal. Whereas SharkBite uses brass for the body, Watts uses a plastic material for its quick-connect fittings instead. Ryan Womeldorf has more than a decade of experience writing. When it comes to a quick repair or an easier installation, both will come in handy. That means if there is any damage to the SharkBite quick-connect fitting, it has to be replaced entirely. look on the label for ", "If the women don't find you handsome, they should at least find you handy. " Come join the discussion about tools, projects, builds, styles, scales, reviews, accessories, classifieds, and more! Though they both have teeth gripping the collect, Watts has fewer teeth. Quick-connect fittings are named because they are fast and easy to install. SharkBite fittings and their brass construction are meant to hold up to higher temperatures. Isn't it amazing that they can join the dissimilar pipes(pex w copper). Are there any tricks? That is not to say that one is worse than the other, but there are clear differences that may influence your choice when it comes time for the repair or installation. You'll notice the warranty policy is the same for series 35 and 45potable water system use only. Nightstands are valuable pieces of your bedrooms design, adding both form and function to the space. Two of the most common options out there for quick-connect fittings are Watts and SharkBite. SharkBite vs. ago I replumbed my utility room water lines using Watts brass and pvc pex fittings. In that instance, they are out of sight which means you would not know if a leak was present. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register. DO NOT BUY WATTS FITTINGS!! When it comes down to it, both the Watts and SharkBite quick-connect fittings have their own unique benefits and uses. Real pain to need to go back and replace when you have other things to do.
If you plan to work with plastic tubing or piping, then the Watts fitting would be better. Not only that, for applications where temperatures are higher, you run the risk of degradation and melting whereas SharkBite would not have that issue. The most glaring difference between the Watts fitting and the SharkBite fitting is the material used to construct the body. After all, what good would a fitting be if water managed to find its way through? The brass ones were the ones setup on their boiler display at the store I was at. Despite their similarities, there are differences between the SharkBite and Watts quick-connect fittings. The worst problem comes when you attempt to sell a home and the buyer hires a Home Inspector who questions these fittings. I am replacing all of the brass ones with the pvc ones for now as they are the ones leaking. I have used many Watts products and they make quality stuff, but that doesn't make them legal. It has been 4 weeks and no leaks. If you have ever worked with a Code inspector, you know that they can have attitudes if you try show or tell them that something is Code Approved. There are specific situations where you would want to use your SharkBite fittings versus when you would want to use Watts fittings. The teeth from the twist-lock will tighten when you try to pull the fitting off, ensuring that it is not going anywhere. Before we get into the comparison of the two, it helps to know what a quick-connect fitting is in the first place. Here are the ones Menards carries since this is the internet. They are both flexible and they both work with each other in a give-take relationship. Indeed. The selling point is in the quick-connect ability. Those rubber O-rings are meant to seal off leaks but can wear and deteriorate over time. . i don't know about watts in particular, but i have used other compression fit. On the other hand, Watts fittings are much better wherever PVC or plastic tubing is involved. At some point in the future I will again have to replumb my utility room with a more permanent product. There may be subtle differences between it and the Watts brand, but the concept is the same. http://media.wattswater.com/ES-QC-10Tees.pdf, http://www.watts.com/pages/_products_details.asp?pid=6632, Ducted heatpump sharing ducts with Wood/oil combo.
Is it possible to disconnect Central Boiler & install an electric boiler connected to the heat exchanger instead. If you plan on working with copper pipes, you cant go wrong with SharkBite fittings, either. Watts fittings are better for small diameter tubing, too. I want to rough in the supply lines for my bar bath and Mud sink. Using them outside runs the risk of the rubber O-ring cracking or splitting. My 2nd season in since using the quick connects I'm finding most off them leak after the system cools down. It tied the old copper piping to new Pex with no problems yet. He deliberated for a while about it because they are so expensive per fitting. I just replumbed part of the house with the Watts quick connect fittings. Using them outside runs the risk of the rubber O-ring cracking or splitting. The teeth are of a durable construct, ensuring that they grip onto the piping or tubing securely and wont bend or break. That brass is lead-free, which allows them to have a higher pressure can temperature tolerance than similar fittings constructed of plastic. The lead-free brass is quite rigid in the same way that a pipe is and can stand up to higher pressure tolerances as well. The rubber is both flexible and durable, and it is also easy to replace in the event of wear and tear or damage. Well, if the fitting is damaged, you can potentially repair it whereas the SharkBite fitting would simply need to be replaced. The Boiler Room - Wood Boilers and Furnaces. They have their own books and don't care how many website copies from fitting manufacturers you show them. SharkBite tends to go best in applications where a sturdier connection is required. After all, most people spend nearly one-third of every day in bed. In that instance, they are out of sight which means you would not know if a leak was present. Help! Watts quick-connect fittings have a locking mechanism that twists.